grf about hall

Home / Sustainability

Sustainability

Nothing wasted.
Everything engineered to last.

From the rubber flash we trim to the cartons we ship in, we keep materials in use. Our approach to the environment, our people and the industries we serve.

Rubber flashPulverized and compounded back
Metal offcutsReused and recycled
PackagingCartons and pallets reused

Our approach

Circular by design.

In a rubber factory, waste is easy to make and easy to throw away. We decided to do the opposite: the flash we trim is ground and goes back into production, metal offcuts are reused, and our packaging makes more than one trip.

At a glance

Sustainability in numbers.

0

Rubber flash to landfill

Trimmed flash is reground and returned to production.

3

Material loops

Rubber, metal and packaging kept in use.

14001

ISO environmental

Environmental management across our factories.

45001

ISO health & safety

Occupational health and safety management.

Circular manufacturing

How the rubber loop works.

Every moulded part leaves a thin rim of excess rubber, called flash. Instead of sending it to waste, we granulate it, pulverize it into rubber powder and compound it back into production:

  1. Deflashing · Flash is trimmed from moulded parts
  2. Granulation · A rubber granulator shreds flash into granules
  3. Pulverization · A pulverizer grinds granules into fine rubber powder
  4. Compounding · Powder is mixed back into the compound on the mill
  5. Moulding · The compound is moulded into new parts
ClosedRubber loop
1DeflashingFlash is trimmed from moulded parts
2GranulationA rubber granulator shreds flash into granules
3PulverizationA pulverizer grinds granules into fine rubber powder
4CompoundingPowder is mixed back into the compound on the mill
5MouldingThe compound is moulded into new parts

Three material loops

Rubber, metal and packaging.

RubberFlash & offcuts

Rubber

Excess rubber from moulding is reground and blended back into production, so it does not leave the factory as waste.

  1. Deflashing of moulded parts
  2. Granulation, then pulverization into rubber powder
  3. Compounding back into production
MetalSteel, stainless & brass

Metal

Offcuts and scrap from machining inserts and moulds are reused in new parts or sent for metal recycling.

  1. Offcuts collected at the machines
  2. Reused for smaller parts and inserts
  3. Remaining scrap sent for recycling
PackagingCartons & pallets

Packaging

Cartons and pallets are reused for our own shipments, so packaging makes more than one trip.

  1. Incoming cartons and pallets kept
  2. Checked and reused for shipments
  3. Damaged packaging sent for recycling

Our framework

Three pillars, one standard.

Environment01
Environment

Responsible production

We manage the environmental side of our work under an ISO 14001 system, from the materials we buy to the scrap we generate.

  • Less waste, scrap and energy in production
  • Pollution prevention in our operations
  • Compliance with environmental regulations
People & safety02
People & safety

Safe hands make good parts

Our ISO 45001 system protects the teams who mix, mould and test every part, and the visitors and contractors who work with them.

  • Hazards identified and controlled
  • Training and involvement in safety
  • Safe and healthy workplaces
Local industry03
Local industry

Made close to where it is used

Producing in our own plants in Saudi Arabia and the UAE keeps supply chains short and supports national manufacturing.

  • Own factories in KSA and the UAE
  • Local stock and technical support
  • Shorter delivery to project sites

Products that cut waste

Less waste on your site too.

Our test plugs replace the welded end caps traditionally used for pressure tests.

The old way

Welded end caps

  • Welded on for every test
  • Cut off and scrapped afterwards
  • Hot work and fire risk on site
  • Pipe ends need re-preparing
The GLOBAL way

Reusable test plugs

  • Fitted in minutes, no welding
  • Removed and reused on the next test
  • No hot work on site
  • Pipe ends left intact
grf ind utilities
We engineer rubber to last, because the most sustainable part is the one you never have to replace.GLOBAL Rubber Factory

Across the life cycle

From design to end of life.

1

Design

Parts are engineered for their real operating conditions, so they last longer in service.

2

Materials

Each compound is chosen for its duty: heat, pressure, oil, water or weather.

3

Manufacturing

Moulding and bonding in our own plants under ISO 14001 and ISO 45001.

4

In service

Reusable test plugs replace welded end caps and avoid hot work on site.

5

End of life

Worn parts are reverse engineered, so equipment stays in service instead of being replaced.

People & safety

Safe hands make good parts.

Training

Everyone is trained for the machines, moulds and materials they work with.

Protective equipment

The right PPE for mixing, moulding, machining and testing.

Safe machinery

Guarded presses and machines, and safe procedures for moulds.

Learning from incidents

Incidents and near misses are reported, investigated and acted on.

How we manage it

Governance and assurance.

Integrated Management System

Quality, environment and health and safety managed as one system across our factories.

Independent certification

Our system is certified to ISO 9001, ISO 14001 and ISO 45001.

Written policies

Environmental and health and safety policies set out what we commit to.

Training & awareness

Our people are trained and involved in safe, responsible ways of working.

Questions about our standards?

Our team can share policies and certificates for your vendor registration or audit.

Request a quote →