ALU-PLUG™ Aluminium Pipe Test Plug

Lightweight aluminium test plug for low-pressure air and water testing of drain, sewer and waste pipes. Nominal sizes 1.5″ – 18″ (40 – 450 mm), fitting pipe I.D. 1.5″ – 20″ (38 – 495 mm); larger sizes on request.

Additional information

Size range

1.5″–18″ (40–450 mm)

Max. back pressure

Up to 30 psi (2.07 bar), by size

Body material

Aluminium plates, zinc-plated steel parts

Application

Pressure testing & line isolation

Nominal size1.5″ – 18″40 – 450 mm
Fits pipe I.D.1.5″ – 20″38 – 495 mm · 20 sizes
Max. back pressureup to 30 psi2.07 bar, by size
BodyAluminium plateszinc-plated steel parts
OptionsSingle / double sealchemical-resistant seals

ALU-PLUG™ seals the end of a pipe for leak testing and low-pressure air or water tests. Its aluminium plates keep the plug strong but light enough to carry in a tool bag. Turn the handle and the plates squeeze the rubber ring, which expands against the pipe wall for a tight seal.

The waterway through the plug lets you fill, vent and drain the line, and release back pressure before you remove the plug. Larger sizes are available on request. Always check the maximum back pressure for your size before the test.

Key features

  • Aluminium plates: strength with low weight
  • Light enough to carry in a tool bag
  • Waterway (½″, 1″ or 2″) to fill, vent, drain and release back pressure
  • Steel parts zinc-plated to a 90-hour salt spray test
  • Chemical-resistant seals available to order
  • Double-seal version available to order
  • Fits PVC, GRP, MDPE / HDPE and carbon steel pipes

How to use

Six steps, one plug.

  1. Insert the plugSlide the plug into the clean pipe end, past the minimum insertion depth.
  2. Tighten the center lockTurn the T-handle until the rubber ring presses firmly on the pipe wall.
  3. Fill with waterConnect the hose to the waterway and fill the section, venting the air.
  4. Pressurize & holdRaise the pressure with the hand pump and hold it for the test time. Watch the gauge.
  5. Release & drainRelease the pressure through the waterway and drain the line.
  6. Remove the plugLoosen the T-handle, pull the plug out and inspect the seal before the next test.

Sizes & part numbers

Find your size.

Enter your pipe inner diameter: every size whose sealing range covers it is highlighted. Part numbers are for aluminium, single seal, single nozzle; other versions on request.

P/N Nominal Fits I.D. Min. insertion Overall length Waterway Max. back pressure Weight
110005 1.5″ · 40 mm 1.5 – 2″38 – 50 mm 1.8″45 mm 3.7″94 mm ½″ 30 psi2.07 bar 0.17 kg
110017 2″ · 50 mm 1.9 – 2.4″49 – 62 mm 1.7″43 mm 3.5″90 mm ½″ 30 psi2.07 bar 0.22 kg
110029 2.5″ · 65 mm 2.4 – 3″62 – 77 mm 1.7″43 mm 3.6″92 mm ½″ 30 psi2.07 bar 0.27 kg
110041 3″ · 75 mm 2.9 – 3.5″73 – 89 mm 1.7″43 mm 3.7″94 mm ½″ 20 psi1.38 bar 0.31 kg
110053 3.5″ · 90 mm 3.3 – 4.1″84 – 103 mm 2.1″53 mm 3.8″96 mm ½″ 15 psi1.03 bar 0.36 kg
110065 4″ · 100 mm 3.7 – 4″94 – 110 mm 1.9″47 mm 3.7″94 mm ½″ 10 psi0.69 bar 0.36 kg
110077 4.5″ · 114 mm 4.4 – 5.1″112 – 130 mm 2.2″56 mm 5.5″140 mm ½″ 10 psi0.69 bar 0.47 kg
110089 5″ · 125 mm 5 – 5.6″125 – 142 mm 2.4″60 mm 3.7″95 mm ½″ 10 psi0.69 bar 0.79 kg
110101 6″ · 150 mm 5.7 – 6.6″146 – 168 mm 1.9″48 mm 3.8″96 mm ½″ 10 psi0.69 bar 0.70 kg
110113 7″ · 175 mm 6.9 – 8″175 – 200 mm 2.5″64 mm 3.9″100 mm 1″ 7 psi0.48 bar 1.92 kg
110125 8″ · 200 mm 7.6 – 8.7″193 – 220 mm 2.5″64 mm 3.9″100 mm 1″ 7 psi0.48 bar 1.59 kg
110137 9″ · 225 mm 8.7 – 9.4″220 – 240 mm 2.5″64 mm 6.7″170 mm 1″ 7 psi0.48 bar 2.06 kg
110149 10″ · 250 mm 9.6 – 11″245 – 270 mm 2.9″73 mm 7″178 mm 1″ 7 psi0.48 bar 2.52 kg
110161 11″ · 275 mm 11 – 13″274 – 328 mm 3.9″100 mm 7.9″200 mm 1″ 7 psi0.48 bar 3.45 kg
110173 12″ · 300 mm 12 – 13″295 – 325 mm 3″77 mm 7.9″200 mm 1″ 7 psi0.48 bar 3.42 kg
110185 13″ · 325 mm 13 – 14″325 – 360 mm 4.7″120 mm 9.1″230 mm 1″ 5 psi0.34 bar 4.75 kg
110197 14″ · 350 mm 14 – 15″350 – 385 mm 4.3″110 mm 8.5″215 mm 1″ 5 psi0.34 bar 6.95 kg
110209 15″ · 375 mm 15 – 16″370 – 410 mm 4.3″110 mm 8.9″225 mm 1″ 5 psi0.34 bar 5.35 kg
110221 16″ · 400 mm 15 – 17″390 – 435 mm 4.3″110 mm 8.9″225 mm 1″ 5 psi0.34 bar 5.90 kg
110233 18″ · 450 mm 18 – 19″445 – 495 mm 4.3″110 mm 8.9″225 mm 2″ 5 psi0.34 bar 8.75 kg

Back pressure is the pressure inside the line acting on the plug. It is the installer’s responsibility never to exceed the value for your size; secure the plug against movement during the test.

Applications

Where it works.

Leak testing of drain, sewer and waste pipes
Air and water tests on new and repaired pipe sections
Works in PVC, GRP, MDPE / HDPE and carbon steel pipes
Manhole and chamber connections
Residential, commercial and municipal drainage

My project 0

Need a different size or pressure rating?

Send us the pipe I.D., material and test pressure. We will confirm the right plug and lead time.

Request a quote →