TRIO-SEAL™ 3S Rubber Ring for PVC & UPVC Pipes

3S sealing ring for push-fit PVC and UPVC pressure pipe joints. Made in EPDM as standard (SBR or other compounds on request) to ASTM F477, for pipe OD from 63 to 630 mm (2.5″ – 24″). It seals the joint and keeps outside water and gas out of the line.

Additional information

Pipe OD

2.5″ – 25″ (63 – 630 mm), 14 sizes; special dimensions on request

Rubber

EPDM standard; SBR, NR or NBR on request

Hardness

60 ± 5 Shore A

Temperature

−22 °F to +212 °F (−30 °C to +100 °C)

Standards

ASTM F477, EN 681-1

Pipe type

PVC, UPVC

Part numbers

310001 – 310028

Pipe OD63 – 630 mm2.5″ – 24″ · 12 sizes
RubberEPDMSBR or other compounds on request
Hardness60 ± 5Shore A (ASTM D2240)
Temperature−22 °F to +212 °F−30 °C to +100 °C
StandardASTM F477EN 681-1

TRIO-SEAL™ is GRF’s 3S rubber ring for the socket joints of PVC and UPVC pipes. Its heel locks into the groove of the socket, and its sealing lips press on the spigot all the way round, so the joint stays tight and no outside water or gas can get into the pipeline.

The ring is made in EPDM as standard, with SBR or other elastomers (NR, NBR) on request. It is moulded to the catalogue dimensions for each pipe size, with tight tolerances on the ring diameter, width and height, and it is made in accordance with ASTM F477 and the main European pipe-seal standards.

The compound is tested for tensile strength, elongation, compression set, heat ageing and ozone resistance, and rings can be supplied to meet potable-water requirements (BS 6920 WRC, KTW). Special dimensions on request.

Key features

  • 3S profile: heel locks in the socket groove, lips seal on the spigot
  • EPDM as standard; SBR, NR or NBR on request
  • Made in accordance with ASTM F477, EN 681-1, EN 1452, EN 1456, DIN 19532, BS 2494, ISO 1398 and AWWA
  • Hardness 60 ± 5 Shore A
  • Tensile strength at least 1,200 psi (8.3 MPa); elongation at least 325 %
  • Compression set 20 % max (24 h at 212 °F / 100 °C)
  • Ozone resistant: no cracks (ASTM D1149)
  • Potable-water versions to BS 6920 WRC (UK) and KTW
  • 12 sizes for pipe OD 63 – 630 mm (2.5″ – 24″); special dimensions on request

How to use

Seven steps, one tight joint.

  1. Know the ringTRIO-SEAL™ sits in the groove of the pipe socket. Its heel locks the ring in place and its sealing lips grip the spigot all the way round.
  2. Clean the socketWipe the socket and the ring groove clean and dry. Sand, dust or old lubricant in the groove can stop the ring from seating.
  3. Fit the ringFold the ring into a heart shape, put it into the socket and let it spring open into the groove, with the lips facing into the pipe.
  4. Check the seatingRun a finger round the inside of the ring. It must sit evenly in the groove all the way round, with no twist or bulge.
  5. Lubricate the ringBrush pipe lubricant onto the exposed face of the ring only. Keep the groove dry so the ring cannot roll out.
  6. Mark & push homeMark the insertion depth on the chamfered spigot. Line the pipes up straight and push the spigot in until the marks reach the socket mouth.
  7. Check the jointThe socket mouth must stop between the two marks. The ring stays in its groove and seals evenly against the spigot.

Sizes & part numbers

Find your size.

Enter your pipe OD in mm: the matching ring is highlighted (nominal inch size shown under it). Each size comes in EPDM (standard) or SBR, with its own part number. Dimensions in mm with tolerances; special dimensions on request.

P/N EPDM P/N SBR Pipe OD DN Ring Ø D Width b Height h
310002 310001 63 mm2.5″ DN50 83.60 mm±0.7 mm 10.30 mm±0.4 mm 18.10 mm±0.4 mm
310004 310003 75 mm3″ DN65 98.00 mm±0.7 mm 11.50 mm±0.4 mm 20.30 mm±0.4 mm
310006 310005 90 mm3.5″ DN80 115.60 mm±0.7 mm 12.80 mm±0.4 mm 22.20 mm±0.4 mm
310008 310007 110 mm4″ DN100 138.40 mm±0.8 mm 14.20 mm±0.4 mm 24.20 mm±0.4 mm
310012 310011 160 mm6″ DN150 194.40 mm±1.0 mm 17.20 mm±0.4 mm 27.80 mm±0.4 mm
310014 310013 200 mm8″ — 238.20 mm±1.0 mm 19.10 mm±0.4 mm 29.50 mm±0.4 mm
310016 310015 225 mm9″ DN200 266.20 mm±1.2 mm 20.60 mm±0.4 mm 31.40 mm±0.4 mm
310018 310017 250 mm10″ — 295.70 mm±1.2 mm 22.85 mm±0.4 mm 35.20 mm±0.4 mm
310022 310021 315 mm12″ DN300 367.80 mm±1.5 mm 26.40 mm±0.5 mm 38.90 mm±0.4 mm
310024 310023 400 mm16″ — 464.00 mm±1.8 mm 32.00 mm±0.5 mm 46.60 mm±0.5 mm
310026 310025 500 mm20″ — 571.60 mm±2.7 mm 34.30 mm±0.6 mm 54.00 mm±1.3 mm
310028 310027 630 mm24″ — 716.50 mm±4.2 mm 40.50 mm±0.6 mm 64.00 mm±1.3 mm

Use only pipe lubricant approved for the ring material and for potable water where needed; never use oil or grease. Keep the groove clean and dry, and do not twist the ring. Store rings away from sunlight, ozone and heat, flat and free of tension.

Applications

Where it works.

PVC and UPVC pressure pipe joints
Potable water networks
Sewer and drainage pipelines
Keeps groundwater and gas out of the line

My project 0

Need a different size or pressure rating?

Send us the pipe I.D., material and test pressure. We will confirm the right plug and lead time.

Request a quote →