Resources · Test plugs & pressure testing

Pick the plug. Work out the pressure.

Find the test plug that fits your pipe and job, estimate the hydrostatic test pressure and convert units. Then send us your request in one form.

Tool 01 · Plug selector

Which plug fits my pipe?

Choose the job, enter your pipe size and the pressure you need. We show the plugs that cover it.

Tool 02 · Test pressure

What test pressure do I need?

A quick first estimate of the hydrostatic test pressure from your design pressure and code.

Minimum test pressure
—

First estimate only. The project specification, the lowest-rated component and the pipe yield strength set the final test pressure. Our engineers confirm it before every test.

Book a hydrostatic test

Tool 03 · Pipe calculator

How much water, how much force?

Enter the pipe bore, the test length and the test pressure. See the water you need to fill it and the force each end plug must hold.

Water to fill—
End force on each plug—
Weight of water—

End force = test pressure × bore area. The plugs and their restraint must hold it with a safety margin. Estimate only: our engineers confirm plugs and restraint for every test.

Tool 04 · Virtual test

Watch your test before it happens.

Enter your pipe and test pressure, then run a virtual hydrostatic test: isolate, fill, vent, pressurise, hold and report, with a live gauge and pressure chart.

  1. 1Isolate
  2. 2Fill
  3. 3Vent air
  4. 4Pressurise
  5. 5Hold
  6. 6Report
0 psi0 bar
Test pressure—
Pressure drop—
Water to fill—
Force on each plug—

Plugs that can run this test

Illustration only: real hold times, pressures and acceptance follow your code and project specification.

Tool 05 · Unit converter

psi, bar, inches and millimetres.

Type in any box. Pipe sizes also show the nearest nominal size.

Guides

Guides worth reading.

Short, practical guides from our engineers on rubber, test plugs and pressure testing.

Choosing a test plug

Mechanical, inflatable or high-pressure?

  • Mechanical plugs squeeze a rubber seal between two plates. Quick to fit, for small and medium pipes at low pressure.
  • Inflatable plugs cover a range of sizes with one plug and suit large sewers and drains. Low working pressure.
  • High-pressure gripping plugs (IN-MAX™, OUT-MAX™, ELBOW-MAX™) lock into steel pipe for hydrotests up to 15,000 psi (1,034 bar).
  • Weld test plugs (DB-WELD™, DBG-WELD™, FLANGE-WELD™) test or isolate a single weld without filling the whole line.

Safety first

  • Never exceed the plug rating or its back pressure.
  • Restrain the plug and keep people out of its line.
  • Use water, vent all air and release pressure before removing a plug.

Hydrostatic testing

Steps, hold time and documents

  • Isolate the section with test plugs or blinds.
  • Fill with water and vent every high point.
  • Raise pressure in steps to the test pressure.
  • Hold for the time the code or project asks for, then inspect for leaks and pressure drop.
  • Record the pressure chart and sign the test report.

Hydrostatic tests use water because it stores far less energy than air at the same pressure. We run tests on site in Saudi Arabia or at our factory.

Glossary

Terms in plain words.

Hydrostatic test
Pressure test with water to prove a pipe or vessel holds pressure without leaking.
Pneumatic test
Pressure test with air or gas. Used only when water cannot be used, with extra safety measures.
Back pressure
Pressure acting on the far side of a plug, trying to push it out of the pipe.
Bypass
A channel through a plug that lets flow pass or lets you fill, vent and drain.
Isolation
Closing off part of a line so work or testing can be done safely.
Double block & bleed (DBB)
Two seals with a bleed point between them, so leakage past the first seal is seen and vented.
Design pressure
The highest pressure a system is designed to carry in service.
MDP / STP
Maximum design pressure and system test pressure, terms used in EN 805 for water supply.
SMYS
Specified minimum yield strength of the pipe steel. Test pressure is limited to a share of it.
Schedule (Sch)
Pipe wall thickness class, such as Sch 40 or Sch 80.
NPS / DN
Nominal pipe size in inches and nominal diameter in millimetres.
Pressure chart
Recorded pressure over the whole test, attached to the test report.
Hold time
How long the test pressure must stay steady for the test to pass.

Send a request

One form. Every request.

Pick what you need, add the details and a drawing or photo if you have one. Our engineers reply by email or phone.

FAQ

About these tools.

Are the tools exact?

They give a fast first answer. Final selections and test pressures depend on your specification, and our engineers confirm them.

Can you make a size or rating that is not listed?

Yes. We make custom plugs, seals and rubber parts. Send the details through the form.

Do you supply samples?

For many standard parts, yes. Choose Sample request in the form.

Not sure where to start?

Tell us the pipe, the pressure or the part. We point you to the right product or service.

Request a quote →