LIPRO-SEAL™ Lip Seal Rubber Ring for PVC-U Pipes & Fittings

Lip seal rubber ring for the socket joints of PVC-U pipes and fittings. It seals the joint and keeps outside liquids and gases out of the line. Made to EN 681-1 in SBR or EPDM, for pipe OD from 40 to 315 mm (1.5″ – 12″).

Additional information

Pipe OD

40 – 315 mm (1.5″ – 12″), 7 sizes; special dimensions on request

Rubber

SBR or EPDM; NR or NBR on request

Temperature

−49 °F to +225 °F (−45 °C to +107 °C)

Standards

EN 681-1, EN 1401, DIN V 19534, BS 2494

Use

PVC-U pipe & fitting socket joints

Part numbers

320001 – 320014

Pipe OD40 – 315 mm1.5″ – 12″ · 7 sizes
RubberSBR or EPDMNR or NBR on request
Temperature−49 °F to +225 °F−45 °C to +107 °C
StandardEN 681-1EN 1401 · DIN V 19534
UsePipes & fittingsPVC-U socket joints

LIPRO-SEAL™ is GRF’s lip seal ring for the socket joints of PVC-U pipes and fittings, such as elbows, tees and couplers. Its ribbed heel sits firmly in the socket groove, and its flexible lip presses on the pipe all the way round, so the joint stays watertight and no outside liquid or gas can get into the pipeline.

The ring is made in SBR or EPDM, with NR or NBR on request, to EN 681-1 and the PVC-U pipe standards EN 1401 and DIN V 19534. It is moulded to tight tolerances on the ring diameter, height and width for each size.

Rings can be supplied to meet potable-water requirements (BS 6920 WRC, UK). Special dimensions on request.

Key features

  • Lip profile: ribbed heel in the groove, flexible lip seals on the pipe
  • For PVC-U pipes and fittings: elbows, tees, couplers and pipe sockets
  • SBR or EPDM; NR or NBR on request
  • Made in accordance with EN 681-1, EN 1401, DIN V 19534 and BS 2494
  • Temperature range −49 °F to +225 °F (−45 °C to +107 °C)
  • Potable-water versions to BS 6920 WRC (UK)
  • 7 sizes for pipe OD 40 – 315 mm (1.5″ – 12″); special dimensions on request

How to use

Seven steps, one tight fitting joint.

  1. Know the ringLIPRO-SEAL™ sits in the groove of the fitting socket. Its ribbed heel holds the ring in place and its lip seals on the pipe all the way round.
  2. Clean the socketWipe the socket of the fitting and the ring groove clean and dry. Sand, dust or old lubricant in the groove can stop the ring from seating.
  3. Fit the ringFold the ring into a heart shape, put it into the fitting socket and let it spring open into the groove, with the lip facing into the fitting.
  4. Check the seatingRun a finger round the inside of the ring. It must sit evenly in the groove all the way round, with no twist or bulge.
  5. Lubricate the ringBrush pipe lubricant onto the exposed face of the ring only. Keep the groove dry so the ring cannot roll out.
  6. Mark & push homeMark the insertion depth on the chamfered pipe end. Line the pipe up with the fitting socket and push it in until the marks reach the socket mouth.
  7. Check the jointThe socket mouth must stop between the two marks. The ring stays in its groove and seals evenly against the pipe.

Sizes & part numbers

Find your size.

Enter your pipe OD in mm: the matching ring is highlighted (nominal inch size shown under it). Each size comes in EPDM or SBR, with its own part number. Dimensions in mm with tolerances; special dimensions on request.

P/N EPDM P/N SBR Pipe OD Ring Ø YD Height A Width B
320002 320001 40 mm1.5″ 52.80 mm±0.6 mm 9.60 mm±0.4 mm 7.70 mm±0.3 mm
320004 320003 50 mm2″ 62.80 mm±0.8 mm 9.60 mm±0.4 mm 7.70 mm±0.3 mm
320006 320005 75 mm3″ 88.90 mm±0.3 mm 9.60 mm±0.4 mm 7.70 mm±0.3 mm
320008 320007 110 mm4″ 124.60 mm±1.0 mm 9.60 mm±0.4 mm 7.70 mm±0.3 mm
320010 320009 160 mm6″ 179.40 mm±1.0 mm 13.30 mm±0.4 mm 10.90 mm±0.4 mm
320012 320011 200 mm8″ 222.60 mm±1.3 mm 14.40 mm±0.4 mm 12.00 mm±0.4 mm
320014 320013 315 mm12″ 337.56 mm±1.3 mm 21.20 mm±0.4 mm 17.07 mm±0.4 mm

Use only pipe lubricant approved for the ring material and for potable water where needed; never use oil or grease. Keep the groove clean and dry, and do not twist the ring. Store rings away from sunlight, ozone and heat, flat and free of tension.

Applications

Where it works.

PVC-U pipe and fitting joints
Sewer and drainage systems
Potable water networks
Keeps outside liquid and gas out of the line

My project 0

Need a different size or pressure rating?

Send us the pipe I.D., material and test pressure. We will confirm the right plug and lead time.

Request a quote →