CL-PLUG™ Center-Lock Pipe Test Plug

Center-lock test plug for low-pressure leak testing with air or water in drain, sewer, stormwater and service lines, in PVC, GRP, MDPE / HDPE and carbon steel pipes. Nominal sizes 0.5″ – 18″ (12 – 450 mm), fitting pipe I.D. 0.5″ – 20″ (12 – 495 mm).

Additional information

Size range

0.5″–18″ (12–450 mm)

Max. back pressure

Up to 50 psi (3.4 bar), by size

Body material

Zinc-plated steel

Application

Pressure testing & line isolation

Nominal size0.5″ – 18″12 – 450 mm
Fits pipe I.D.0.5″ – 20″12 – 495 mm · 24 sizes
Max. back pressureup to 50 psi3.4 bar, by size
BodyZinc-plated steelalso aluminium & stainless
OptionsSingle / double sealsingle / double nozzle

CL-PLUG™ seals the end of a pipe for leak testing and low-pressure air or water tests. Turn the T-handle and the center lock compresses the rubber ring, which expands evenly against the pipe wall for a tight seal.

One person can fit it on site. The waterway through the plug lets you fill, vent and drain the line, and release back pressure before you remove the plug. Always check the maximum back pressure for your size before the test.

Key features

  • Center-lock T-handle: one person fits it in seconds
  • Even rubber expansion for a tight seal on the pipe wall
  • Waterway (½″ or 1″) to fill, vent, drain and release back pressure
  • Thrust washers fitted as standard on every size
  • Zinc-plated steel, tested to 90 hours of salt spray
  • Robust build for site work
  • Fits PVC, GRP, MDPE / HDPE and carbon steel pipes

How to use

Six steps, one plug.

  1. Insert the plugSlide the plug into the clean pipe end, past the minimum insertion depth.
  2. Tighten the center lockTurn the T-handle until the rubber ring presses firmly on the pipe wall.
  3. Fill with waterConnect the hose to the waterway and fill the section, venting the air.
  4. Pressurize & holdRaise the pressure with the hand pump and hold it for the test time. Watch the gauge.
  5. Release & drainRelease the pressure through the waterway and drain the line.
  6. Remove the plugLoosen the T-handle, pull the plug out and inspect the seal before the next test.

Sizes & part numbers

Find your size.

Enter your pipe inner diameter: every size whose sealing range covers it is highlighted. Part numbers are for steel, single seal, single nozzle; other versions on request.

Photo P/N Nominal Fits I.D. Min. insertion Overall length Waterway Max. back pressure Weight
130001 0.5″ · 12 mm 0.5 – 0.6″12 – 16 mm 2.6″66 mm 4.3″110 mm 4 mm 50 psi3.45 bar 40 g
130002 0.75″ · 19 mm 0.75 – 1″19 – 26.5 mm 2.6″66 mm 4.3″110 mm 6 mm 50 psi3.45 bar 50 g
130003 1″ · 25 mm 1 – 1.5″24.8 – 37.5 mm 2.6″66 mm 4.3″110 mm 6 mm 50 psi3.45 bar 70 g
130004 1.25″ · 32 mm 1.2 – 1.6″31 – 39.5 mm 2.6″66 mm 4.3″110 mm 6 mm 50 psi3.45 bar 90 g
110001 1.5″ · 40 mm 1.5 – 2″37 – 50 mm 1.2″31 mm 3.2″81.5 mm ½″ 30 psi2.07 bar 0.16 kg
110013 2″ · 50 mm 2 – 2.4″50 – 61 mm 1.3″32.7 mm 3.3″82.8 mm ½″ 30 psi2.07 bar 0.18 kg
110025 2.5″ · 65 mm 2.4 – 3″61 – 75 mm 1.3″33.2 mm 3.2″80.5 mm ½″ 30 psi2.07 bar 0.26 kg
110037 3″ · 75 mm 2.9 – 3.3″73 – 85 mm 1.3″34 mm 3.2″80.5 mm ½″ 20 psi1.38 bar 0.28 kg
110049 3.5″ · 89 mm 3.3 – 4″84 – 100 mm 1.6″41 mm 3.2″81 mm ½″ 15 psi1.03 bar 0.36 kg
110061 4″ · 100 mm 3.7 – 4.3″94 – 108 mm 1.5″37.5 mm 3.3″83.3 mm ½″ 10 psi0.69 bar 0.41 kg
110073 4.5″ · 114 mm 4 – 5″110 – 125 mm 1.6″40 mm 3.3″83.3 mm ½″ 10 psi0.69 bar 0.58 kg
110085 5″ · 125 mm 4.9 – 5.5″124 – 139 mm 1.5″37 mm 3.3″83.3 mm ½″ 10 psi0.69 bar 0.60 kg
110097 6″ · 150 mm 6 – 6″150 – 160 mm 1.6″39.7 mm 3.3″83.3 mm ½″ 10 psi0.69 bar 0.75 kg
110109 7″ · 175 mm 6.9 – 8″175 – 200 mm 1.8″46 mm 5.1″130 mm 1″ 7 psi0.48 bar 1.56 kg
110121 8″ · 200 mm 7.7 – 8.5″195 – 215 mm 1.5″37 mm 5.1″130 mm 1″ 7 psi0.48 bar 1.47 kg
110133 9″ · 225 mm 8.3 – 9.1″210 – 230 mm 2.3″58 mm 5.9″150 mm 1″ 7 psi0.48 bar 1.93 kg
110145 10″ · 250 mm 9.6 – 10″245 – 260 mm 2.2″55 mm 5.9″150 mm 1″ 7 psi0.48 bar 2.55 kg
110157 11″ · 275 mm 9.4 – 11″240 – 282 mm 2.2″55 mm 8.3″210 mm 1″ 7 psi0.48 bar 3.20 kg
110169 12″ · 300 mm 12 – 13″296 – 320 mm 3.3″85 mm 5.9″150 mm 1″ 7 psi0.48 bar 3.72 kg
110181 13″ · 325 mm 11 – 14″290 – 345 mm 3.3″85 mm 8.3″210 mm 1″ 7 psi0.48 bar 3.80 kg
110193 14″ · 350 mm 13 – 15″340 – 385 mm 3.3″85 mm 8.3″210 mm 1″ 5 psi0.34 bar 6.54 kg
110205 15″ · 375 mm 15 – 16″370 – 415 mm 3.9″100 mm 8.3″210 mm 1″ 5 psi0.34 bar 7.00 kg
110217 16″ · 400 mm 15 – 17″390 – 430 mm 3.7″95 mm 8.3″210 mm 1″ 5 psi0.34 bar 8.45 kg
110229 18″ · 450 mm 18 – 19″448 – 495 mm 3.9″100 mm 8.7″220 mm 1″ 5 psi0.34 bar 10.6 kg

Back pressure is the pressure inside the line acting on the plug. Never exceed the value for your size, and secure the plug against movement during the test.

Applications

Where it works.

Leak testing of drain, sewer and stormwater lines
Air and water tests on new and repaired pipe sections
Works in PVC, GRP, MDPE / HDPE and carbon steel pipes
Manhole and chamber connections
Residential, commercial and municipal drainage

My project 0

Need a different size or pressure rating?

Send us the pipe I.D., material and test pressure. We will confirm the right plug and lead time.

Request a quote →